With a private air conditioning service in Aydın city centre (Efeler), the process starts with describing the unit and the problem accurately when you report the fault. The technician inspects the air conditioner on site, identifies the cause of the fault through measurements, and tells you what work is needed and what it will cost before starting. The repair is carried out with your approval, the air conditioner is then run to check it, and the service report you sign is sent to your email as a PDF.
Why Are Air Conditioners in Aydın Under So Much Strain?
Aydın city centre (Efeler) is an area that sees very high temperatures in the summer months. During this period, air conditioners often run at full capacity from midday until late at night. Long periods of non-stop running put strain on parts such as the compressor, fan motors, capacitors and the electronic board. In a unit whose maintenance is overdue, a dirty filter and a dusty condenser add to this and make a fault more likely.
That is why air conditioner faults in Aydın usually appear in the hottest weeks. Knowing how the process works from the start makes things easier for you and helps the fault get fixed correctly and quickly.
Before making a service request, you can do a few simple checks yourself: make sure cooling mode is selected on the remote control and that the set temperature is below room temperature, check the remote control batteries, remove and clean the filters, and make sure nothing in front of the units is blocking the airflow. If these do not solve the problem, or if there is a burning smell, smoke or the fuse trips, switch the air conditioner off and contact a technician. Do not try to open the unit's covers, electrical board or pipe connections yourself.
Step 1: What Information Should You Share When Reporting a Fault?
The information you give when making a service request helps the technician arrive properly prepared. It is useful to share the following:
- Make and model: A photo of the label on the side of the indoor unit or on the outdoor unit is enough.
- The problem: Briefly describe what you have noticed – not cooling, not working at all, leaking water, making a noise, giving off a smell and so on.
- Error code: If there is a code or flashing light on the display, write it down or photograph it. The meaning of codes varies by brand and model; the technician assesses it according to the unit.
- When the problem started: Did the fault start suddenly, or has performance dropped over time?
- Age of the unit and last service: The approximate installation date and when it was last serviced.
- Location of the outdoor unit: Is it on a balcony, an exterior wall or the roof? This is important for planning the equipment needed.
You can make your request through the service request form, by phone or via WhatsApp. Sending photos and a short video makes the initial assessment easier.
Step 2: On-Site Inspection and Fault Diagnosis
When the technician arrives, they first listen to you describe the problem and run the air conditioner to see the symptom for themselves. A systematic check of the indoor and outdoor units then follows:
- The condition of the filter, evaporator and condensate drain line
- Whether the outdoor unit fan and compressor are starting up
- The power supply, connections and electrical parts such as the capacitor
- Measured values such as system pressure and outlet air temperature
- Any signs of leaks at the pipe connections
Fault diagnosis should be based on measurement, not guesswork. For example, weak cooling can be caused by a dirty filter, the outdoor unit fan or a refrigerant leak, and each has a different solution. If low refrigerant is found, it is important to remember that this is not normal consumption – there is a leak in the system. A refrigerant (gas) recharge done without finding and repairing the leak is not a permanent solution.
Although some faults may at first seem to have a single cause, more than one problem can be present at the same time. For example, in an air conditioner that has run with a dirty filter for a long time, airflow may have dropped and the outdoor unit may also have been under extra strain. So the technician looks not only at the symptom you reported but also at the overall condition of the unit, and points out any other risks they see separately.
Step 3: Information Before Any Work Begins
Once the cause of the fault has been identified, the technician explains the following to you:
- What the fault is and why it happened
- Which part will be repaired or replaced
- Whether the work will be done on site or a part needs to be sourced
- The total cost
The cost is given before work starts, and nothing is done without your approval. You also get a clear assessment of whether the repair makes sense given the age of the unit. This way you will not face an unexpected bill, and the decision stays entirely with you.
If an additional problem that was not visible at the start comes to light during the repair, the same rule applies: the technician stops work, explains the new situation and the extra cost, and only continues once you have given your approval.
Step 4: Repair and Operational Check Afterwards
The repair is carried out once you have given your approval. When parts are replaced, parts suitable for the unit are used; if a refrigerant leak has been repaired, the system is recharged correctly for the refrigerant type the unit uses (R32, R410A or, in older models, R22).
The job is not considered finished as soon as the repair is complete. The air conditioner is run for a while to check its cooling and heating performance, that the outdoor unit starts up properly, that the condensate drain is working and that there is no unusual noise. The work carried out is then explained to you.
Finally, you sign the service report on the phone and it is sent to your email address as a PDF. This report lists the work done and the parts used. A written guarantee is given on parts and labour; if you have a problem covered by the guarantee, this report makes your claim easier.
Our Service Area in Aydın City Centre
Evime Servis's head office is in İncirliova, close to Aydın city centre (Efeler). We serve various neighbourhoods of Efeler, in particular Zafer, Mimar Sinan, Girne, Ilıca, Kurtuluş and Cumhuriyet, and we can reach most requests on the same day. As well as air conditioners, you can see our Aydın technical service page for boiler, household appliance and cooker hood–hob faults. Evime Servis is an independent private technical service and is not the authorised service of any brand. You can find out what to look for when choosing a service for different brands of air conditioner in our article on choosing a private service for different air conditioner brands.
If you have a fault with your air conditioner in Aydın city centre, you can book through our Aydın private air conditioning service page or the service request form, or contact us by phone or WhatsApp on +90 256 503 48 80.
Frequently asked questions
Do I need to know the error code when reporting a fault?
No, but if you see a code on the display it is useful to write it down. Because the meaning of codes varies by brand and model, the technician assesses it on the unit itself.
When will I find out the cost?
Once the fault has been diagnosed on site, you are told the cost before any work begins. No repair is started without your approval.
What happens if the same problem comes back after the repair?
A written guarantee is given on parts and labour. Contacting us with the service report sent to your email makes your claim easier.
If a part is needed, will the repair be finished on the same day?
If we have the part with us, the repair is usually done on the same visit. If a part needs to be sourced, the estimated time is explained to you when you are informed before the work.
Private air conditioning service in your area
We diagnose the fault on site, tell you the price before starting and guarantee the repair in writing.
Published: 25.10.2026 · Last updated: